Install the car on the two-rack-mount elevator.

Disconnect a battery room батарю.

Install adaptation on a brake pedal to reduce amount of the following brake fluid.

Merge coolant from a refrigerating contour.

Remove the top covers of the engine.

Fig. 6.85. Fastening of the panel of access to the air filter: 1 – fastening bolts

Turn off two bolts of fastening of the panel of access to the air filter (fig. 6.85).

Fig. 6.86. Removal of the muffler of noise of an admission: 1 – fastening bolt; 2 – muffler of noise of an admission

Turn off a bolt of fastening of the muffler of noise of an admission and remove its (fig. 6.86).

ATTENTION Do not damage a branch pipe of selection of depression on an inlet collector. At its breakage replace an inlet collector.

Disconnect a hose of selection of depression of the vacuum amplifier of brakes from an inlet collector.

Disconnect blocks of wires from ignition coils.

Disconnect a block of wires from the block of a butterfly valve.

Fig. 6.87. A detachment of a block of wires from the air temperature sensor: 1 – block of wires of the sensor of air temperature; 2 – plait of wires

Disconnect a block of wires from the sensor of the air temperature (fig. 6.87).

Disconnect a plait of wires from holders on the engine.

Fig. 6.88. Detachment of a hose of system of catching of vapors of fuel: 1 – hose of system of catching of vapors of fuel

Disconnect a hose of system of catching of vapors of fuel from holders (fig. 6.88).

Turn off a bolt of fastening of the case of the air filter. Do not take out the filter case from a motor compartment.

Fig. 6.89. Removal of the filtering element and the case of the air filter: 1 – the filtering element; 2 – case of the air filter

Remove the filtering element and the case of the air filter (fig. 6.89).

Fig. 6.90. Removal of the block of a butterfly valve: 1 – fastening bolts

Turn off bolts of fastening and remove the block of a butterfly valve (fig. 6.90).

Fig. 6.91. Removal of fastening of an inlet collector: 1 – fastening bolts

Turn off bolts of fastening and remove an inlet collector (fig. 6.91).

Remove fastenings of the noise screen, and then – the screen.

Fig. 6.92. Removal of a lifting eye and pipeline of a refrigerating contour of the conditioner: 1 – lifting eye; 2 – pipeline of a refrigerating contour of the conditioner

Remove a lifting eye and the pipeline of a refrigerating contour of the conditioner between a flange on a board of a front and a receiver dehumidifier (fig. 6.92).

Remove a bolt of fastening of a tip of a wire of "mass" of EBU ABS.

Separate the EBU socket.

Unscrew unions of fastening of pipelines to the hydroblock.

Disconnect pipelines from the hydroblock.

Fig. 6.93. Removal of fastening of an arm of the hydroblock: 1 – fastening bolts

Turn off bolts of fastening of an arm of the hydroblock (fig. 6.93).

Remove the hydroblock assembled with an arm.

Turn off bolts of fastening of the hydroblock to an arm and remove the hydroblock.

Installation is made as it should be, the return to removal.

Fig. 6.94. Installation of the hydroblock

ATTENTION Direct a tip of a wire of "mass" of the hydroblock down to provide tightness of the EBU socket of the hydroblock (fig. 6.94).

Install the pipeline of a refrigerating contour of the conditioner.

Tighten the required moment:

– bolts of fastening of an arm of the hydroblock (6,5 N · l);

– bolts of fastening of pipelines on the hydroblock (14 N · l);

– bolts of fastening of an inlet collector (9 N · l);

– bolts of fastening of the hydroblock to an arm (8 N · м).

NOTE Replace laying at each removal of the block of a butterfly valve. Surely replace laying on the ends of the pipeline of a refrigerating contour of the conditioner.

Remove air from the brake system.

Connect the rechargeable battery.

Execute a repeated reinitsialization of the programmed extreme provisions of a butterfly valve.

Fill with coolant a refrigerating contour.

Check operability of the air conditioning system during the operation of the electric fan of salon at the maximum speed.

If in salon not cooled air moves, find a coolant utecheka.

NOTE Cars are equipped with electric pumps of two types: for the ABS system, or for the ABS system joint with system of stabilization of a trajectory.

Fig. 6.95. Schematic diagram of the electric pump